Q941FSoft seal electric floating ball valve is a flange connection, floating ball through ball valve. The sealing form is soft seal. The sealing surface of valve seat is made of fluoroplastic, nominal pressure is pn16-pn63, nominal size is DN 15-dn200, applicable temperature is - 28-300 ℃, valve body material is carbon steel or stainless steel, q941f soft seal electric floating ball valve is suitable for two position cut-off and adjustment. The valve is directly connected with the actuator, which is composed of fine and small electric actuator (or different types of electronic electric actuator or air piston actuator can be configured according to user requirements) and ultra short ball valve. The electric actuator has a built-in servo system, which can be controlled by inputting 4-20mA signal and 220V AC power supply without additional servo amplifier. Compared with ordinary electric ball valve, it has the advantages of compact structure, small volume, light weight, close distance between valve seat and end face flange, less material retention and superior sealing performance.

Q941FPerformance parameters of soft seal electric floating ball valve

model	PN	working pressure / MPa	Applicable temperature / ℃	Applicable media
	16	1.6	-28～300	Water, steam, oil, etc
Q941F-25	25	2.5
Q941F-40	40	4
Q941F-63	63	6.3
Q941F-16P	16	1.6		Corrosive medium such as nitric acid
Q941F-25P	25	2.5
Q941F-40P	40	4
Q941F-63P	63	6.3
Q941F-16R	16	1.6
Q941F-25R	25	2.5
Q941F-40R	40	4
Q941F-63R	63	6.3

 

Q941FSoft seal electric floating ball valve parts materials
 

model	Material Science
	valve body	Ball, stem	seal ring	Packing, gasket
Q941F-16C	WCB	2Cr13	teflon	V-shaped polytetrafluoroethylene, flexible graphite ring, polytetrafluoroethylene sheet, flexible graphite winding gasket
Q941F-25
Q941F-40
Q941F-63
Q941F-16P	ZG1Cr18Ni9Ti	1Cr18Ni9Ti
Q941F-25P
Q941F-40P
Q941F-63P
Q941F-16R	CF8 (304)	0Cr18Ni9 (304)
Q941F-25R
Q941F-40R
Q941F-63R

 

Q941F-16 External structure and dimension of V-type soft seal electric floating ball valve(mm)

DN	L	D	D1	D2	b	z×φd
15	130	95	65	45	14	4×φ14
20	140	105	75	55	14	4×φ14
25	150	115	85	65	14	4×φ14
32	165	135	100	78	16	4×φ18
40	180	145	110	85	16	4×φ18
50	200	160	125	100	16	4×φ18
65	220	180	145	120	18	4×φ18
80	250	195	160	135	20	8×φ18
100	280	215	180	155	20	8×φ18
125	320	245	210	185	22	8×φ18
150	360	280	240	210	24	8×φ23
200	400	335	295	265	26	12×φ23

Q941F-25 External structure and dimension of V-type soft seal electric floating ball valve(mm)

DN	L	D	D1	D2	b	z×φd
15	130	95	65	45	16	4×φ14
20	140	105	75	55	16	4×φ14
25	150	115	85	65	16	4×φ14
32	165	135	100	78	18	4×φ18
40	180	145	110	85	18	4×φ18
50	200	160	125	100	20	4×φ18
65	220	180	145	120	22	8×φ18
80	250	195	160	135	22	8×φ18
100	280	230	190	160	24	8×φ23
125	320	270	220	188	28	8×φ25
150	360	300	250	218	30	8×φ25
200	400	360	310	278	34	12×φ25

Q941F-40 External structure and dimension of V-type soft seal electric floating ball valve(mm)

DN	L	D	D1	D2	b	z×φd
15	130	95	65	45	16	4×φ14
20	140	105	75	55	16	4×φ14
25	150	115	85	65	16	4×φ14
32	180	135	100	78	18	4×φ18
40	200	145	110	85	18	4×φ18
50	220	160	125	100	20	4×φ18
65	250	180	145	120	22	8×φ18
80	280	195	160	135	22	8×φ18
100	320	230	190	160	24	8×φ23
125	400	270	220	188	28	8×φ25
150	400	300	250	218	30	8×φ25
200	502	375	320	282	38	12×φ30

Q941F-63 External structure and dimension of V-type soft seal electric floating ball valve(mm)

DN	L	D	D1	D2	b	z×φd
15	140	105	75	55	18	4×φ14
20	152	125	90	68	20	4×φ18
25	180	135	100	78	22	4×φ18
32	200	150	110	82	24	4×φ23
40	220	165	125	95	24	4×φ23
50	250	175	135	105	26	4×φ23
65	280	200	160	130	28	8×φ23
80	320	210	170	140	30	8×φ23
100	360	250	200	168	32	8×φ25
125	381	295	240	202	36	8×φ34
150	403	340	280	240	38	12×φ34

1. Be careful in installation and construction, and do not hit the valve.
2. Before installation, the ball valve should be inspected to check the specification and model, and identify whether there is damage, especially for the valve stem. Turn it a few times to see if it is skewed, because Zui is prone to bump the stem during transportation. Also remove the debris in the valve.
3. When lifting the ball valve, the rope should not be tied to the hand wheel or the valve stem to avoid damage to these parts, but should be tied to the valve body.
4. The pipeline connected to the ball valve must be cleaned. Compressed air can be used to blow away iron oxide chips, mud and sand, welding slag and other impurities. These debris, not only easy to scratch the sealing surface of the ball valve, in which large particles of debris (such as welding slag), but also block the small valve, so that its failure.
5. The position of valve handle rotation should be reserved during installation. 6. The ball valve cannot be used as throttling. 7. The ball valve with transmission mechanism shall be installed vertically.